Discussion:
[PATCH v8 0/4] mfd: add support for Diolan DLN-2
(too old to reply)
Octavian Purdila
2014-10-15 14:48:07 UTC
Permalink
Raw Message
This patch series adds support for Diolan USB-I2C/GPIO Master Adapter
DLN-2. Details about device can be found here:

https://www.diolan.com/i2c/i2c_interface.html.

Changes since v7:

* MFD: add results parameter to dln2_transfer to allow receiving the
hardware result code; also fix dln2_transfer to return error only
if the result code is > 0x80;

* GPIO: update to the new dln2_transfer API

* I2C: update to the new dln2_transfer API, use DECLARE_BITMAP, use
new_cb as a variable name instead of new, update the Kconfig help
to mentioned DLN2_I2C and DLN2_GPIO, remove i2c_setup as it is not
useful anymore after removing the frequency code

Changes since v6:

* MFD: make sure DLN2_HANDLE_EVENT stays 0, move a few operations out
of the lock block, renamed one missed _rx_callback function to
_event_callback, speed-up disconnect by checking for it in
find_free_slot, remove the URB submit helper and simplify URB
resubmit code, use mfd_add_hotplug_devices, change the driver name
to dln2 (from usb-dln2), initialize disconnect_lock

* GPIO: no changes

* I2C: keep sorting in Kconfig and Makefile, add warning for transfers
bigger then DLN2_I2C_MAX_XFER_SIZE, remove frequency code - I will
send a separate patch that moves this to i2c core, revert to using
tx structures for dln2_i2c_enable


Daniel Baluta (1):
gpio: add support for the Diolan DLN-2 USB GPIO driver

Laurentiu Palcu (1):
i2c: add support for Diolan DLN-2 USB-I2C adapter

Octavian Purdila (2):
mfd: add support for Diolan DLN-2 devices
gpiolib: add irq_not_threaded flag to gpio_chip

drivers/gpio/Kconfig | 12 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-dln2.c | 557 +++++++++++++++++++++++++++++++
drivers/gpio/gpiolib.c | 2 +-
drivers/i2c/busses/Kconfig | 10 +
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-dln2.c | 270 +++++++++++++++
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/dln2.c | 756 ++++++++++++++++++++++++++++++++++++++++++
include/linux/gpio/driver.h | 3 +
include/linux/mfd/dln2.h | 69 ++++
12 files changed, 1692 insertions(+), 1 deletion(-)
create mode 100644 drivers/gpio/gpio-dln2.c
create mode 100644 drivers/i2c/busses/i2c-dln2.c
create mode 100644 drivers/mfd/dln2.c
create mode 100644 include/linux/mfd/dln2.h
--
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to ***@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Octavian Purdila
2014-10-15 14:48:08 UTC
Permalink
Raw Message
This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO
Master Adapter DLN-2. Details about the device can be found here:

https://www.diolan.com/i2c/i2c_interface.html.

Information about the USB protocol can be found in the Programmer's
Reference Manual [1], see section 1.7.

Because the hardware has a single transmit endpoint and a single
receive endpoint the communication between the various DLN2 drivers
and the hardware will be muxed/demuxed by this driver.

Each DLN2 module will be identified by the handle field within the DLN2
message header. If a DLN2 module issues multiple commands in parallel
they will be identified by the echo counter field in the message header.

The DLN2 modules can use the dln2_transfer() function to issue a
command and wait for its response. They can also register a callback
that is going to be called when a specific event id is generated by
the device (e.g. GPIO interrupts). The device uses handle 0 for
sending events.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Octavian Purdila <***@intel.com>
---
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/dln2.c | 756 +++++++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/dln2.h | 69 +++++
4 files changed, 837 insertions(+)
create mode 100644 drivers/mfd/dln2.c
create mode 100644 include/linux/mfd/dln2.h

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index c9200d3..4538815a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -189,6 +189,17 @@ config MFD_DA9063
Additional drivers must be enabled in order to use the functionality
of the device.

+config MFD_DLN2
+ tristate "Diolan DLN2 support"
+ select MFD_CORE
+ depends on USB
+ help
+
+ This adds support for Diolan USB-I2C/SPI/GPIO Master Adapter
+ DLN-2. Additional drivers such as I2C_DLN2, GPIO_DLN2,
+ etc. must be enabled in order to use the functionality of
+ the device.
+
config MFD_MC13XXX
tristate
depends on (SPI_MASTER || I2C)
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 61f8dbf..2cd7e74 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -175,6 +175,7 @@ obj-$(CONFIG_MFD_STW481X) += stw481x.o
obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o
obj-$(CONFIG_MFD_MENF21BMC) += menf21bmc.o
obj-$(CONFIG_MFD_HI6421_PMIC) += hi6421-pmic-core.o
+obj-$(CONFIG_MFD_DLN2) += dln2.o

intel-soc-pmic-objs := intel_soc_pmic_core.o intel_soc_pmic_crc.o
obj-$(CONFIG_INTEL_SOC_PMIC) += intel-soc-pmic.o
diff --git a/drivers/mfd/dln2.c b/drivers/mfd/dln2.c
new file mode 100644
index 0000000..124b262
--- /dev/null
+++ b/drivers/mfd/dln2.c
@@ -0,0 +1,756 @@
+/*
+ * Driver for the Diolan DLN-2 USB adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ * i2c-diolan-u2c.c
+ * Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/usb.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/dln2.h>
+#include <linux/rculist.h>
+
+struct dln2_header {
+ __le16 size;
+ __le16 id;
+ __le16 echo;
+ __le16 handle;
+} __packed;
+
+struct dln2_response {
+ struct dln2_header hdr;
+ __le16 result;
+} __packed;
+
+#define DLN2_GENERIC_MODULE_ID 0x00
+#define DLN2_GENERIC_CMD(cmd) DLN2_CMD(cmd, DLN2_GENERIC_MODULE_ID)
+#define CMD_GET_DEVICE_VER DLN2_GENERIC_CMD(0x30)
+#define CMD_GET_DEVICE_SN DLN2_GENERIC_CMD(0x31)
+
+#define DLN2_HW_ID 0x200
+#define DLN2_USB_TIMEOUT 200 /* in ms */
+#define DLN2_MAX_RX_SLOTS 16
+#define DLN2_MAX_URBS 16
+#define DLN2_RX_BUF_SIZE 512
+
+enum dln2_handle {
+ DLN2_HANDLE_EVENT = 0, /* don't change, hardware defined */
+ DLN2_HANDLE_CTRL,
+ DLN2_HANDLE_GPIO,
+ DLN2_HANDLE_I2C,
+ DLN2_HANDLES
+};
+
+/*
+ * Receive context used between the receive demultiplexer and the
+ * transfer routine. While sending a request the transfer routine
+ * will look for a free receive context and use it to wait for a
+ * response and to receive the URB and thus the response data.
+ */
+struct dln2_rx_context {
+ /* completion used to wait for a response */
+ struct completion done;
+
+ /* if non-NULL the URB contains the response */
+ struct urb *urb;
+
+ /* if true then this context is used to wait for a response */
+ bool in_use;
+};
+
+/*
+ * Receive contexts for a particular DLN2 module (i2c, gpio, etc.). We
+ * use the handle header field to identify the module in
+ * dln2_dev.mod_rx_slots and then the echo header field to index the
+ * slots field and find the receive context for a particular request.
+ */
+struct dln2_mod_rx_slots {
+ /* RX slots bitmap */
+ DECLARE_BITMAP(bmap, DLN2_MAX_RX_SLOTS);
+
+ /* used to wait for a free RX slot */
+ wait_queue_head_t wq;
+
+ /* used to wait for an RX operation to complete */
+ struct dln2_rx_context slots[DLN2_MAX_RX_SLOTS];
+
+ /* avoid races between alloc/free_rx_slot and dln2_rx_transfer */
+ spinlock_t lock;
+};
+
+struct dln2_dev {
+ struct usb_device *usb_dev;
+ struct usb_interface *interface;
+ u8 ep_in;
+ u8 ep_out;
+
+ struct urb *rx_urb[DLN2_MAX_URBS];
+ void *rx_buf[DLN2_MAX_URBS];
+
+ struct dln2_mod_rx_slots mod_rx_slots[DLN2_HANDLES];
+
+ struct list_head event_cb_list;
+ spinlock_t event_cb_lock;
+
+ bool disconnect;
+ int active_transfers;
+ wait_queue_head_t disconnect_wq;
+ spinlock_t disconnect_lock;
+};
+
+struct dln2_event_cb_entry {
+ struct list_head list;
+ u16 id;
+ struct platform_device *pdev;
+ dln2_event_cb_t callback;
+};
+
+int dln2_register_event_cb(struct platform_device *pdev, u16 id,
+ dln2_event_cb_t rx_cb)
+{
+ struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
+ struct dln2_event_cb_entry *i, *new_cb;
+ unsigned long flags;
+ int ret = 0;
+
+ new_cb = kmalloc(sizeof(*new_cb), GFP_KERNEL);
+ if (!new_cb)
+ return -ENOMEM;
+
+ new_cb->id = id;
+ new_cb->callback = rx_cb;
+ new_cb->pdev = pdev;
+
+ spin_lock_irqsave(&dln2->event_cb_lock, flags);
+
+ list_for_each_entry(i, &dln2->event_cb_list, list) {
+ if (i->id == id) {
+ ret = -EBUSY;
+ break;
+ }
+ }
+
+ if (!ret)
+ list_add_rcu(&new_cb->list, &dln2->event_cb_list);
+
+ spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
+
+ if (ret)
+ kfree(new_cb);
+
+ return ret;
+}
+EXPORT_SYMBOL(dln2_register_event_cb);
+
+void dln2_unregister_event_cb(struct platform_device *pdev, u16 id)
+{
+ struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
+ struct dln2_event_cb_entry *i;
+ unsigned long flags;
+ bool found = false;
+
+ spin_lock_irqsave(&dln2->event_cb_lock, flags);
+
+ list_for_each_entry(i, &dln2->event_cb_list, list) {
+ if (i->id == id) {
+ list_del_rcu(&i->list);
+ found = true;
+ break;
+ }
+ }
+
+ spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
+
+ if (found) {
+ synchronize_rcu();
+ kfree(i);
+ }
+}
+EXPORT_SYMBOL(dln2_unregister_event_cb);
+
+static bool dln2_rx_transfer(struct dln2_dev *dln2, struct urb *urb,
+ u16 handle, u16 rx_slot)
+{
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
+ struct dln2_rx_context *rxc;
+ bool ret = false;
+
+ rxc = &rxs->slots[rx_slot];
+
+ /*
+ * No need to disable interrupts as this lock is not taken in
+ * interrupt context elsewhere in this driver and this
+ * function (or its callers) are not exported to other
+ * modules.
+ */
+ spin_lock(&rxs->lock);
+ if (rxc->in_use && !rxc->urb) {
+ rxc->urb = urb;
+ complete(&rxc->done);
+ ret = true;
+ }
+ spin_unlock(&rxs->lock);
+
+ return ret;
+}
+
+static void dln2_run_event_callbacks(struct dln2_dev *dln2, u16 id, u16 echo,
+ void *data, int len)
+{
+ struct dln2_event_cb_entry *i;
+
+ rcu_read_lock();
+
+ list_for_each_entry_rcu(i, &dln2->event_cb_list, list)
+ if (i->id == id)
+ i->callback(i->pdev, echo, data, len);
+
+ rcu_read_unlock();
+}
+
+static void dln2_rx(struct urb *urb)
+{
+ struct dln2_dev *dln2 = urb->context;
+ struct dln2_header *hdr = urb->transfer_buffer;
+ struct device *dev = &dln2->interface->dev;
+ u16 id, echo, handle, size;
+ u8 *data;
+ int len;
+ int err;
+
+ switch (urb->status) {
+ case 0:
+ /* success */
+ break;
+ case -ECONNRESET:
+ case -ENOENT:
+ case -ESHUTDOWN:
+ case -EPIPE:
+ /* this urb is terminated, clean up */
+ dev_dbg(dev, "urb shutting down with status %d\n", urb->status);
+ return;
+ default:
+ dev_dbg(dev, "nonzero urb status received %d\n", urb->status);
+ goto out;
+ }
+
+ if (urb->actual_length < sizeof(struct dln2_header)) {
+ dev_err(dev, "short response: %d\n", urb->actual_length);
+ goto out;
+ }
+
+ handle = le16_to_cpu(hdr->handle);
+ id = le16_to_cpu(hdr->id);
+ echo = le16_to_cpu(hdr->echo);
+ size = le16_to_cpu(hdr->size);
+
+ if (size != urb->actual_length) {
+ dev_err(dev, "size mismatch: handle %x cmd %x echo %x size %d actual %d\n",
+ handle, id, echo, size, urb->actual_length);
+ goto out;
+ }
+
+ if (handle >= DLN2_HANDLES) {
+ dev_warn(dev, "RX: invalid handle %d\n", handle);
+ goto out;
+ }
+
+ data = urb->transfer_buffer + sizeof(struct dln2_header);
+ len = urb->actual_length - sizeof(struct dln2_header);
+
+ if (handle == DLN2_HANDLE_EVENT) {
+ dln2_run_event_callbacks(dln2, id, echo, data, len);
+ } else {
+ /* URB will be re-submitted in free_rx_slot */
+ if (dln2_rx_transfer(dln2, urb, handle, echo))
+ return;
+ dev_warn(dev, "bad/late response %d/%d\n", handle, echo);
+ }
+
+out:
+ err = usb_submit_urb(urb, GFP_ATOMIC);
+ if (err < 0)
+ dev_err(dev, "failed to resubmit RX URB: %d\n", err);
+}
+
+static void *dln2_prep_buf(u16 handle, u16 cmd, u16 echo, const void *obuf,
+ int *obuf_len, gfp_t gfp)
+{
+ int len;
+ void *buf;
+ struct dln2_header *hdr;
+
+ len = *obuf_len + sizeof(*hdr);
+ buf = kmalloc(len, gfp);
+ if (!buf)
+ return NULL;
+
+ hdr = (struct dln2_header *)buf;
+ hdr->id = cpu_to_le16(cmd);
+ hdr->size = cpu_to_le16(len);
+ hdr->echo = cpu_to_le16(echo);
+ hdr->handle = cpu_to_le16(handle);
+
+ memcpy(buf + sizeof(*hdr), obuf, *obuf_len);
+
+ *obuf_len = len;
+
+ return buf;
+}
+
+static int dln2_send_wait(struct dln2_dev *dln2, u16 handle, u16 cmd, u16 echo,
+ const void *obuf, int obuf_len)
+{
+ int ret = 0;
+ int len = obuf_len;
+ void *buf;
+ int actual;
+
+ buf = dln2_prep_buf(handle, cmd, echo, obuf, &len, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ ret = usb_bulk_msg(dln2->usb_dev,
+ usb_sndbulkpipe(dln2->usb_dev, dln2->ep_out),
+ buf, len, &actual, DLN2_USB_TIMEOUT);
+
+ kfree(buf);
+
+ return ret;
+}
+
+static bool find_free_slot(struct dln2_dev *dln2, u16 handle, int *slot)
+{
+ struct dln2_mod_rx_slots *rxs;
+ unsigned long flags;
+
+ if (dln2->disconnect) {
+ *slot = -ENODEV;
+ return true;
+ }
+
+ rxs = &dln2->mod_rx_slots[handle];
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ *slot = find_first_zero_bit(rxs->bmap, DLN2_MAX_RX_SLOTS);
+
+ if (*slot < DLN2_MAX_RX_SLOTS) {
+ struct dln2_rx_context *rxc = &rxs->slots[*slot];
+
+ set_bit(*slot, rxs->bmap);
+ rxc->in_use = true;
+ }
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+
+ return *slot < DLN2_MAX_RX_SLOTS;
+}
+
+static int alloc_rx_slot(struct dln2_dev *dln2, u16 handle)
+{
+ int ret;
+ int slot;
+
+ /*
+ * No need to timeout here, the wait is bounded by the timeout
+ * in _dln2_transfer.
+ */
+ ret = wait_event_interruptible(dln2->mod_rx_slots[handle].wq,
+ find_free_slot(dln2, handle, &slot));
+ if (ret < 0)
+ return ret;
+
+ return slot;
+}
+
+static void free_rx_slot(struct dln2_dev *dln2, u16 handle, int slot)
+{
+ struct dln2_mod_rx_slots *rxs;
+ struct urb *urb = NULL;
+ unsigned long flags;
+ struct dln2_rx_context *rxc;
+
+ rxs = &dln2->mod_rx_slots[handle];
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ clear_bit(slot, rxs->bmap);
+
+ rxc = &rxs->slots[slot];
+ rxc->in_use = false;
+ urb = rxc->urb;
+ rxc->urb = NULL;
+ reinit_completion(&rxc->done);
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+
+ if (urb) {
+ int err;
+ struct device *dev = &dln2->interface->dev;
+
+ err = usb_submit_urb(urb, GFP_KERNEL);
+ if (err < 0)
+ dev_err(dev, "failed to resubmit RX URB: %d\n", err);
+ }
+
+ wake_up_interruptible(&rxs->wq);
+}
+
+static int _dln2_transfer(struct dln2_dev *dln2, u16 handle, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len, u16 *result)
+{
+ int ret = 0;
+ int rx_slot;
+ struct dln2_response *rsp;
+ struct dln2_rx_context *rxc;
+ struct device *dev = &dln2->interface->dev;
+ const int timeout = DLN2_USB_TIMEOUT * HZ / 1000;
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
+
+ spin_lock(&dln2->disconnect_lock);
+ if (!dln2->disconnect)
+ dln2->active_transfers++;
+ else
+ ret = -ENODEV;
+ spin_unlock(&dln2->disconnect_lock);
+
+ if (ret)
+ return ret;
+
+ rx_slot = alloc_rx_slot(dln2, handle);
+ if (rx_slot < 0) {
+ ret = rx_slot;
+ goto out_decr;
+ }
+
+ ret = dln2_send_wait(dln2, handle, cmd, rx_slot, obuf, obuf_len);
+ if (ret < 0) {
+ dev_err(dev, "USB write failed: %d\n", ret);
+ goto out_free_rx_slot;
+ }
+
+ rxc = &rxs->slots[rx_slot];
+
+ ret = wait_for_completion_interruptible_timeout(&rxc->done, timeout);
+ if (ret <= 0) {
+ if (!ret)
+ ret = -ETIMEDOUT;
+ goto out_free_rx_slot;
+ }
+
+ if (dln2->disconnect) {
+ ret = -ENODEV;
+ goto out_free_rx_slot;
+ }
+
+ /* if we got here we know that the response header has been checked */
+ rsp = rxc->urb->transfer_buffer;
+
+ if (rsp->hdr.size < sizeof(*rsp)) {
+ ret = -EPROTO;
+ goto out_free_rx_slot;
+ }
+
+ if (result)
+ *result = le16_to_cpu(rsp->result);
+ if (le16_to_cpu(rsp->result) > 0x80) {
+ dev_dbg(dev, "%d received response with error %d\n",
+ handle, le16_to_cpu(rsp->result));
+ ret = -EREMOTEIO;
+ goto out_free_rx_slot;
+ }
+
+ if (!ibuf) {
+ ret = 0;
+ goto out_free_rx_slot;
+ }
+
+ if (*ibuf_len > rsp->hdr.size - sizeof(*rsp))
+ *ibuf_len = rsp->hdr.size - sizeof(*rsp);
+
+ memcpy(ibuf, rsp + 1, *ibuf_len);
+
+out_free_rx_slot:
+ free_rx_slot(dln2, handle, rx_slot);
+out_decr:
+ spin_lock(&dln2->disconnect_lock);
+ dln2->active_transfers--;
+ spin_unlock(&dln2->disconnect_lock);
+ if (dln2->disconnect)
+ wake_up(&dln2->disconnect_wq);
+
+ return ret;
+}
+
+int dln2_transfer(struct platform_device *pdev, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len, u16 *result)
+{
+ struct dln2_platform_data *dln2_pdata;
+ struct dln2_dev *dln2;
+ u16 handle;
+
+ dln2 = dev_get_drvdata(pdev->dev.parent);
+ dln2_pdata = dev_get_platdata(&pdev->dev);
+ handle = dln2_pdata->handle;
+
+ return _dln2_transfer(dln2, handle, cmd, obuf, obuf_len, ibuf, ibuf_len,
+ result);
+}
+EXPORT_SYMBOL(dln2_transfer);
+
+static int dln2_check_hw(struct dln2_dev *dln2)
+{
+ int ret;
+ __le32 hw_type;
+ int len = sizeof(hw_type);
+
+ ret = _dln2_transfer(dln2, DLN2_HANDLE_CTRL, CMD_GET_DEVICE_VER,
+ NULL, 0, &hw_type, &len, NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(hw_type))
+ return -EREMOTEIO;
+
+ if (le32_to_cpu(hw_type) != DLN2_HW_ID) {
+ dev_err(&dln2->interface->dev, "Device ID 0x%x not supported\n",
+ le32_to_cpu(hw_type));
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int dln2_print_serialno(struct dln2_dev *dln2)
+{
+ int ret;
+ __le32 serial_no;
+ int len = sizeof(serial_no);
+ struct device *dev = &dln2->interface->dev;
+
+ ret = _dln2_transfer(dln2, DLN2_HANDLE_CTRL, CMD_GET_DEVICE_SN, NULL, 0,
+ &serial_no, &len, NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(serial_no))
+ return -EREMOTEIO;
+
+ dev_info(dev, "Diolan DLN2 serial 0x%x\n", le32_to_cpu(serial_no));
+
+ return 0;
+}
+
+static int dln2_hw_init(struct dln2_dev *dln2)
+{
+ int ret;
+
+ ret = dln2_check_hw(dln2);
+ if (ret < 0)
+ return ret;
+
+ return dln2_print_serialno(dln2);
+}
+
+static void dln2_free_rx_urbs(struct dln2_dev *dln2)
+{
+ int i;
+
+ for (i = 0; i < DLN2_MAX_URBS; i++) {
+ usb_kill_urb(dln2->rx_urb[i]);
+ usb_free_urb(dln2->rx_urb[i]);
+ kfree(dln2->rx_buf[i]);
+ }
+}
+
+static void dln2_free(struct dln2_dev *dln2)
+{
+ dln2_free_rx_urbs(dln2);
+ usb_put_dev(dln2->usb_dev);
+ kfree(dln2);
+}
+
+static int dln2_setup_rx_urbs(struct dln2_dev *dln2,
+ struct usb_host_interface *hostif)
+{
+ int i;
+ const int rx_max_size = DLN2_RX_BUF_SIZE;
+
+ for (i = 0; i < DLN2_MAX_URBS; i++) {
+ int ret;
+ struct device *dev = &dln2->interface->dev;
+
+ dln2->rx_buf[i] = kmalloc(rx_max_size, GFP_KERNEL);
+ if (!dln2->rx_buf[i])
+ return -ENOMEM;
+
+ dln2->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
+ if (!dln2->rx_urb[i])
+ return -ENOMEM;
+
+ usb_fill_bulk_urb(dln2->rx_urb[i], dln2->usb_dev,
+ usb_rcvbulkpipe(dln2->usb_dev, dln2->ep_in),
+ dln2->rx_buf[i], rx_max_size, dln2_rx, dln2);
+
+ ret = usb_submit_urb(dln2->rx_urb[i], GFP_KERNEL);
+ if (ret < 0) {
+ dev_err(dev, "failed to submit RX URB: %d\n", ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static struct dln2_platform_data dln2_pdata_gpio = {
+ .handle = DLN2_HANDLE_GPIO,
+};
+
+/* Only one I2C port seems to be supported on current hardware */
+static struct dln2_platform_data dln2_pdata_i2c = {
+ .handle = DLN2_HANDLE_I2C,
+ .port = 0,
+};
+
+static const struct mfd_cell dln2_devs[] = {
+ {
+ .name = "dln2-gpio",
+ .platform_data = &dln2_pdata_gpio,
+ .pdata_size = sizeof(struct dln2_platform_data),
+ },
+ {
+ .name = "dln2-i2c",
+ .platform_data = &dln2_pdata_i2c,
+ .pdata_size = sizeof(struct dln2_platform_data),
+ },
+};
+
+static void dln2_disconnect(struct usb_interface *interface)
+{
+ struct dln2_dev *dln2 = usb_get_intfdata(interface);
+ int i, j;
+
+ /* don't allow starting new transfers */
+ spin_lock(&dln2->disconnect_lock);
+ dln2->disconnect = true;
+ spin_unlock(&dln2->disconnect_lock);
+
+ /* cancel in progress transfers */
+ for (i = 0; i < DLN2_HANDLES; i++) {
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[i];
+ unsigned long flags;
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ /* cancel all response waiters */
+ for (j = 0; j < DLN2_MAX_RX_SLOTS; j++) {
+ struct dln2_rx_context *rxc = &rxs->slots[j];
+
+ if (rxc->in_use)
+ complete(&rxc->done);
+ }
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+ }
+
+ /* wait for transfers to end */
+ wait_event(dln2->disconnect_wq, !dln2->active_transfers);
+
+ mfd_remove_devices(&interface->dev);
+
+ dln2_free(dln2);
+}
+
+static int dln2_probe(struct usb_interface *interface,
+ const struct usb_device_id *usb_id)
+{
+ struct usb_host_interface *hostif = interface->cur_altsetting;
+ struct device *dev = &interface->dev;
+ struct dln2_dev *dln2;
+ int ret;
+ int i, j;
+
+ if (hostif->desc.bInterfaceNumber != 0 ||
+ hostif->desc.bNumEndpoints < 2)
+ return -ENODEV;
+
+ dln2 = kzalloc(sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->ep_out = hostif->endpoint[0].desc.bEndpointAddress;
+ dln2->ep_in = hostif->endpoint[1].desc.bEndpointAddress;
+ dln2->usb_dev = usb_get_dev(interface_to_usbdev(interface));
+ dln2->interface = interface;
+ usb_set_intfdata(interface, dln2);
+ init_waitqueue_head(&dln2->disconnect_wq);
+
+ for (i = 0; i < DLN2_HANDLES; i++) {
+ init_waitqueue_head(&dln2->mod_rx_slots[i].wq);
+ spin_lock_init(&dln2->mod_rx_slots[i].lock);
+ for (j = 0; j < DLN2_MAX_RX_SLOTS; j++)
+ init_completion(&dln2->mod_rx_slots[i].slots[j].done);
+ }
+
+ spin_lock_init(&dln2->event_cb_lock);
+ spin_lock_init(&dln2->disconnect_lock);
+ INIT_LIST_HEAD(&dln2->event_cb_list);
+
+ ret = dln2_setup_rx_urbs(dln2, hostif);
+ if (ret)
+ goto out_cleanup;
+
+ ret = dln2_hw_init(dln2);
+ if (ret < 0) {
+ dev_err(dev, "failed to initialize hardware\n");
+ goto out_cleanup;
+ }
+
+ ret = mfd_add_hotplug_devices(dev, dln2_devs, ARRAY_SIZE(dln2_devs));
+ if (ret != 0) {
+ dev_err(dev, "failed to add mfd devices to core\n");
+ goto out_cleanup;
+ }
+
+ return 0;
+
+out_cleanup:
+ dln2_free(dln2);
+
+ return ret;
+}
+
+static const struct usb_device_id dln2_table[] = {
+ { USB_DEVICE(0xa257, 0x2013) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(usb, dln2_table);
+
+static struct usb_driver dln2_driver = {
+ .name = "dln2",
+ .probe = dln2_probe,
+ .disconnect = dln2_disconnect,
+ .id_table = dln2_table,
+};
+
+module_usb_driver(dln2_driver);
+
+MODULE_AUTHOR("Octavian Purdila <***@intel.com>");
+MODULE_DESCRIPTION("Core driver for the Diolan DLN2 interface adapter");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/dln2.h b/include/linux/mfd/dln2.h
new file mode 100644
index 0000000..57ddc58
--- /dev/null
+++ b/include/linux/mfd/dln2.h
@@ -0,0 +1,69 @@
+#ifndef __LINUX_USB_DLN2_H
+#define __LINUX_USB_DLN2_H
+
+#define DLN2_CMD(cmd, id) ((cmd) | ((id) << 8))
+
+struct dln2_platform_data {
+ u16 handle; /* sub-driver handle (internally used only) */
+ u8 port; /* I2C/SPI port */
+};
+
+/**
+ * dln2_event_cb_t - event callback function signature
+ *
+ * @pdev - the sub-device that registered this callback
+ * @echo - the echo header field received in the message
+ * @data - the data payload
+ * @len - the data payload length
+ *
+ * The callback function is called in interrupt context and the data
+ * payload is only valid during the call. If the user needs later
+ * access of the data, it must copy it.
+ */
+
+typedef void (*dln2_event_cb_t)(struct platform_device *pdev, u16 echo,
+ const void *data, int len);
+
+/**
+ * dl2n_register_event_cb - register a callback function for an event
+ *
+ * @pdev - the sub-device that registers the callback
+ * @event - the event for which to register a callback
+ * @event_cb - the callback function
+ *
+ * @return 0 in case of success, negative value in case of error
+ */
+int dln2_register_event_cb(struct platform_device *pdev, u16 event,
+ dln2_event_cb_t event_cb);
+
+/**
+ * dln2_unregister_event_cb - unregister the callback function for an event
+ *
+ * @pdev - the sub-device that registered the callback
+ * @event - the event for which to register a callback
+ */
+void dln2_unregister_event_cb(struct platform_device *pdev, u16 event);
+
+/**
+ * dln2_transfer - issue a DLN2 command and wait for a response and
+ * the associated data
+ *
+ * @pdev - the sub-device which is issuing this transfer
+ * @cmd - the command to be sent to the device
+ * @obuf - the buffer to be sent to the device; it can be NULL if the
+ * user doesn't need to transmit data with this command
+ * @obuf_len - the size of the buffer to be sent to the device
+ * @ibuf - any data associated with the response will be copied here;
+ * it can be NULL if the user doesn't need the response data
+ * @ibuf_len - must be initialized to the input buffer size; it will
+ * be modified to indicate the actual data transfered;
+ * @result - pointer to store the result code received from hardware;
+ * it can be NULL if the user doesn't need the result code
+ *
+ * @return 0 for success, negative value for errors
+ */
+int dln2_transfer(struct platform_device *pdev, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len, u16 *result);
+
+#endif
--
1.9.1
Octavian Purdila
2014-10-15 14:48:11 UTC
Permalink
Raw Message
From: Daniel Baluta <***@intel.com>

This patch adds GPIO and IRQ support for the Diolan DLN-2 GPIO module.

Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 2.9 for the GPIO
module commands and responses.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Daniel Baluta <***@intel.com>
Signed-off-by: Octavian Purdila <***@intel.com>
---
drivers/gpio/Kconfig | 12 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-dln2.c | 557 +++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 570 insertions(+)
create mode 100644 drivers/gpio/gpio-dln2.c

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 9de1515..44ec206 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -897,4 +897,16 @@ config GPIO_VIPERBOARD
River Tech's viperboard.h for detailed meaning
of the module parameters.

+config GPIO_DLN2
+ tristate "Diolan DLN2 GPIO support"
+ depends on MFD_DLN2
+ select GPIOLIB_IRQCHIP
+
+ help
+ Select this option to enable GPIO driver for the Diolan DLN2
+ board.
+
+ This driver can also be built as a module. If so, the module
+ will be called gpio-dln2.
+
endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 5d024e3..eaa97a0 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_GPIO_CRYSTAL_COVE) += gpio-crystalcove.o
obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
obj-$(CONFIG_GPIO_DA9055) += gpio-da9055.o
obj-$(CONFIG_GPIO_DAVINCI) += gpio-davinci.o
+obj-$(CONFIG_GPIO_DLN2) += gpio-dln2.o
obj-$(CONFIG_GPIO_DWAPB) += gpio-dwapb.o
obj-$(CONFIG_GPIO_EM) += gpio-em.o
obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o
diff --git a/drivers/gpio/gpio-dln2.c b/drivers/gpio/gpio-dln2.c
new file mode 100644
index 0000000..70c25af
--- /dev/null
+++ b/drivers/gpio/gpio-dln2.c
@@ -0,0 +1,557 @@
+/*
+ * Driver for the Diolan DLN-2 USB-GPIO adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_GPIO_ID 0x01
+
+#define DLN2_GPIO_GET_PIN_COUNT DLN2_CMD(0x01, DLN2_GPIO_ID)
+#define DLN2_GPIO_SET_DEBOUNCE DLN2_CMD(0x04, DLN2_GPIO_ID)
+#define DLN2_GPIO_GET_DEBOUNCE DLN2_CMD(0x05, DLN2_GPIO_ID)
+#define DLN2_GPIO_PORT_GET_VAL DLN2_CMD(0x06, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_VAL DLN2_CMD(0x0B, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_OUT_VAL DLN2_CMD(0x0C, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_OUT_VAL DLN2_CMD(0x0D, DLN2_GPIO_ID)
+#define DLN2_GPIO_CONDITION_MET_EV DLN2_CMD(0x0F, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_ENABLE DLN2_CMD(0x10, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_DISABLE DLN2_CMD(0x11, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_DIRECTION DLN2_CMD(0x13, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_DIRECTION DLN2_CMD(0x14, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_EVENT_CFG DLN2_CMD(0x1E, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_EVENT_CFG DLN2_CMD(0x1F, DLN2_GPIO_ID)
+
+#define DLN2_GPIO_EVENT_NONE 0
+#define DLN2_GPIO_EVENT_CHANGE 1
+#define DLN2_GPIO_EVENT_LVL_HIGH 2
+#define DLN2_GPIO_EVENT_LVL_LOW 3
+#define DLN2_GPIO_EVENT_CHANGE_RISING 0x11
+#define DLN2_GPIO_EVENT_CHANGE_FALLING 0x21
+#define DLN2_GPIO_EVENT_MASK 0x0F
+
+#define DLN2_GPIO_MAX_PINS 32
+
+struct dln2_irq_work {
+ struct work_struct work;
+ struct dln2_gpio *dln2;
+ int pin;
+ int type;
+};
+
+struct dln2_gpio {
+ struct platform_device *pdev;
+ struct gpio_chip gpio;
+
+ /*
+ * Cache pin direction to save us one transfer, since the
+ * hardware has separate commands to read the in and out
+ * values.
+ */
+ DECLARE_BITMAP(output_enabled, DLN2_GPIO_MAX_PINS);
+
+ DECLARE_BITMAP(irqs_masked, DLN2_GPIO_MAX_PINS);
+ DECLARE_BITMAP(irqs_enabled, DLN2_GPIO_MAX_PINS);
+ DECLARE_BITMAP(irqs_pending, DLN2_GPIO_MAX_PINS);
+ struct dln2_irq_work *irq_work;
+};
+
+struct dln2_gpio_pin {
+ __le16 pin;
+};
+
+struct dln2_gpio_pin_val {
+ __le16 pin __packed;
+ u8 value;
+};
+
+static int dln2_gpio_get_pin_count(struct platform_device *pdev)
+{
+ int ret;
+ __le16 count;
+ int len = sizeof(count);
+
+ ret = dln2_transfer(pdev, DLN2_GPIO_GET_PIN_COUNT, NULL, 0, &count,
+ &len, NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(count))
+ return -EPROTO;
+
+ return le16_to_cpu(count);
+}
+
+static int dln2_gpio_pin_cmd(struct dln2_gpio *dln2, int cmd, unsigned pin)
+{
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(pin),
+ };
+
+ return dln2_transfer(dln2->pdev, cmd, &req, sizeof(req), NULL, NULL,
+ NULL);
+}
+
+static int dln2_gpio_pin_val(struct dln2_gpio *dln2, int cmd, unsigned int pin)
+{
+ int ret;
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(pin),
+ };
+ struct dln2_gpio_pin_val rsp;
+ int len = sizeof(rsp);
+
+ ret = dln2_transfer(dln2->pdev, cmd, &req, sizeof(req), &rsp, &len,
+ NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(rsp) || req.pin != rsp.pin)
+ return -EPROTO;
+
+ return rsp.value;
+}
+
+static int dln2_gpio_pin_get_in_val(struct dln2_gpio *dln2, unsigned int pin)
+{
+ int ret;
+
+ ret = dln2_gpio_pin_val(dln2, DLN2_GPIO_PIN_GET_VAL, pin);
+ if (ret < 0)
+ return ret;
+ return !!ret;
+}
+
+static int dln2_gpio_pin_get_out_val(struct dln2_gpio *dln2, unsigned int pin)
+{
+ int ret;
+
+ ret = dln2_gpio_pin_val(dln2, DLN2_GPIO_PIN_GET_OUT_VAL, pin);
+ if (ret < 0)
+ return ret;
+ return !!ret;
+}
+
+static void dln2_gpio_pin_set_out_val(struct dln2_gpio *dln2,
+ unsigned int pin, int value)
+{
+ struct dln2_gpio_pin_val req = {
+ .pin = cpu_to_le16(pin),
+ .value = cpu_to_le16(value),
+ };
+
+ dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_SET_OUT_VAL, &req, sizeof(req),
+ NULL, NULL, NULL);
+}
+
+#define DLN2_GPIO_DIRECTION_IN 0
+#define DLN2_GPIO_DIRECTION_OUT 1
+
+static int dln2_gpio_request(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(offset),
+ };
+ struct dln2_gpio_pin_val rsp;
+ int len = sizeof(rsp);
+ int ret;
+
+ ret = dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_ENABLE, offset);
+ if (ret < 0)
+ return ret;
+
+ /* cache the pin direction */
+ ret = dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_GET_DIRECTION,
+ &req, sizeof(req), &rsp, &len, NULL);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(rsp) || req.pin != rsp.pin) {
+ ret = -EPROTO;
+ goto out_disable;
+ }
+
+ switch (rsp.value) {
+ case DLN2_GPIO_DIRECTION_IN:
+ clear_bit(offset, dln2->output_enabled);
+ return 0;
+ case DLN2_GPIO_DIRECTION_OUT:
+ set_bit(offset, dln2->output_enabled);
+ return 0;
+ default:
+ ret = -EPROTO;
+ goto out_disable;
+ }
+
+out_disable:
+ dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_DISABLE, offset);
+ return ret;
+}
+
+static void dln2_gpio_free(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_DISABLE, offset);
+}
+
+static int dln2_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ if (test_bit(offset, dln2->output_enabled))
+ return GPIOF_DIR_OUT;
+
+ return GPIOF_DIR_IN;
+}
+
+static int dln2_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ int dir;
+
+ dir = dln2_gpio_get_direction(chip, offset);
+ if (dir < 0)
+ return dir;
+
+ if (dir == GPIOF_DIR_IN)
+ return dln2_gpio_pin_get_in_val(dln2, offset);
+
+ return dln2_gpio_pin_get_out_val(dln2, offset);
+}
+
+static void dln2_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ dln2_gpio_pin_set_out_val(dln2, offset, value);
+}
+
+static int dln2_gpio_set_direction(struct gpio_chip *chip, unsigned offset,
+ unsigned dir)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ struct dln2_gpio_pin_val req = {
+ .pin = cpu_to_le16(offset),
+ .value = cpu_to_le16(dir),
+ };
+ int ret;
+
+ ret = dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_SET_DIRECTION,
+ &req, sizeof(req), NULL, NULL, NULL);
+ if (ret < 0)
+ return ret;
+
+ if (dir == DLN2_GPIO_DIRECTION_OUT)
+ set_bit(offset, dln2->output_enabled);
+ else
+ clear_bit(offset, dln2->output_enabled);
+
+ return ret;
+}
+
+static int dln2_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ return dln2_gpio_set_direction(chip, offset, DLN2_GPIO_DIRECTION_IN);
+}
+
+static int dln2_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ return dln2_gpio_set_direction(chip, offset, DLN2_GPIO_DIRECTION_OUT);
+}
+
+static int dln2_gpio_set_debounce(struct gpio_chip *chip, unsigned offset,
+ unsigned debounce)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ __le32 duration = cpu_to_le32(debounce);
+
+ return dln2_transfer(dln2->pdev, DLN2_GPIO_SET_DEBOUNCE,
+ &duration, sizeof(duration), NULL, NULL, NULL);
+}
+
+static int dln2_gpio_set_event_cfg(struct dln2_gpio *dln2, unsigned pin,
+ unsigned type, unsigned period)
+{
+ struct {
+ __le16 pin;
+ u8 type;
+ __le16 period;
+ } __packed req = {
+ .pin = cpu_to_le16(pin),
+ .type = type,
+ .period = cpu_to_le16(period),
+ };
+
+ return dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_SET_EVENT_CFG,
+ &req, sizeof(req), NULL, NULL, NULL);
+}
+
+static void dln2_irq_work(struct work_struct *w)
+{
+ struct dln2_irq_work *iw = container_of(w, struct dln2_irq_work, work);
+ struct dln2_gpio *dln2 = iw->dln2;
+ u8 type = iw->type & DLN2_GPIO_EVENT_MASK;
+
+ if (test_bit(iw->pin, dln2->irqs_enabled))
+ dln2_gpio_set_event_cfg(dln2, iw->pin, type, 0);
+ else
+ dln2_gpio_set_event_cfg(dln2, iw->pin, DLN2_GPIO_EVENT_NONE, 0);
+}
+
+static void dln2_irq_enable(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ set_bit(pin, dln2->irqs_enabled);
+ schedule_work(&dln2->irq_work[pin].work);
+}
+
+static void dln2_irq_disable(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ clear_bit(pin, dln2->irqs_enabled);
+ schedule_work(&dln2->irq_work[pin].work);
+}
+
+static void dln2_irq_mask(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ set_bit(pin, dln2->irqs_masked);
+}
+
+static void dln2_irq_unmask(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ struct device *dev = dln2->gpio.dev;
+ int pin = irqd_to_hwirq(irqd);
+
+ if (test_and_clear_bit(pin, dln2->irqs_pending)) {
+ int irq;
+
+ irq = irq_find_mapping(dln2->gpio.irqdomain, pin);
+ if (!irq) {
+ dev_err(dev, "pin %d not mapped to IRQ\n", pin);
+ return;
+ }
+
+ generic_handle_irq(irq);
+ }
+}
+
+static int dln2_irq_set_type(struct irq_data *irqd, unsigned type)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ switch (type) {
+ case IRQ_TYPE_LEVEL_HIGH:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_LVL_HIGH;
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_LVL_LOW;
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE;
+ break;
+ case IRQ_TYPE_EDGE_RISING:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE_RISING;
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE_FALLING;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static struct irq_chip dln2_gpio_irqchip = {
+ .name = "dln2-irq",
+ .irq_enable = dln2_irq_enable,
+ .irq_disable = dln2_irq_disable,
+ .irq_mask = dln2_irq_mask,
+ .irq_unmask = dln2_irq_unmask,
+ .irq_set_type = dln2_irq_set_type,
+};
+
+static void dln2_gpio_event(struct platform_device *pdev, u16 echo,
+ const void *data, int len)
+{
+ int pin, irq;
+ const struct {
+ __le16 count;
+ __u8 type;
+ __le16 pin;
+ __u8 value;
+ } __packed *event = data;
+ struct dln2_gpio *dln2 = platform_get_drvdata(pdev);
+
+ if (len < sizeof(*event)) {
+ dev_err(dln2->gpio.dev, "short event message\n");
+ return;
+ }
+
+ pin = le16_to_cpu(event->pin);
+ if (pin >= dln2->gpio.ngpio) {
+ dev_err(dln2->gpio.dev, "out of bounds pin %d\n", pin);
+ return;
+ }
+
+ irq = irq_find_mapping(dln2->gpio.irqdomain, pin);
+ if (!irq) {
+ dev_err(dln2->gpio.dev, "pin %d not mapped to IRQ\n", pin);
+ return;
+ }
+
+ if (!test_bit(pin, dln2->irqs_enabled))
+ return;
+ if (test_bit(pin, dln2->irqs_masked)) {
+ set_bit(pin, dln2->irqs_pending);
+ return;
+ }
+
+ switch (dln2->irq_work[pin].type) {
+ case DLN2_GPIO_EVENT_CHANGE_RISING:
+ if (event->value)
+ generic_handle_irq(irq);
+ break;
+ case DLN2_GPIO_EVENT_CHANGE_FALLING:
+ if (!event->value)
+ generic_handle_irq(irq);
+ break;
+ default:
+ generic_handle_irq(irq);
+ }
+}
+
+static int dln2_gpio_probe(struct platform_device *pdev)
+{
+ struct dln2_gpio *dln2;
+ struct device *dev = &pdev->dev;
+ int pins;
+ int i, ret;
+
+ pins = dln2_gpio_get_pin_count(pdev);
+ if (pins < 0) {
+ dev_err(dev, "failed to get pin count: %d\n", pins);
+ return pins;
+ }
+ if (pins > DLN2_GPIO_MAX_PINS) {
+ pins = DLN2_GPIO_MAX_PINS;
+ dev_warn(dev, "clamping pins to %d\n", DLN2_GPIO_MAX_PINS);
+ }
+
+ dln2 = devm_kzalloc(&pdev->dev, sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->irq_work = devm_kcalloc(&pdev->dev, pins,
+ sizeof(struct dln2_irq_work), GFP_KERNEL);
+ if (!dln2->irq_work)
+ return -ENOMEM;
+ for (i = 0; i < pins; i++) {
+ INIT_WORK(&dln2->irq_work[i].work, dln2_irq_work);
+ dln2->irq_work[i].pin = i;
+ dln2->irq_work[i].dln2 = dln2;
+ }
+
+ dln2->pdev = pdev;
+
+ dln2->gpio.label = "dln2";
+ dln2->gpio.dev = dev;
+ dln2->gpio.owner = THIS_MODULE;
+ dln2->gpio.base = -1;
+ dln2->gpio.ngpio = pins;
+ dln2->gpio.exported = true;
+ dln2->gpio.can_sleep = true;
+ dln2->gpio.irq_not_threaded = true;
+ dln2->gpio.set = dln2_gpio_set;
+ dln2->gpio.get = dln2_gpio_get;
+ dln2->gpio.request = dln2_gpio_request;
+ dln2->gpio.free = dln2_gpio_free;
+ dln2->gpio.get_direction = dln2_gpio_get_direction;
+ dln2->gpio.direction_input = dln2_gpio_direction_input;
+ dln2->gpio.direction_output = dln2_gpio_direction_output;
+ dln2->gpio.set_debounce = dln2_gpio_set_debounce;
+
+ platform_set_drvdata(pdev, dln2);
+
+ ret = gpiochip_add(&dln2->gpio);
+ if (ret < 0) {
+ dev_err(dev, "failed to add gpio chip: %d\n", ret);
+ goto out;
+ }
+
+ ret = gpiochip_irqchip_add(&dln2->gpio, &dln2_gpio_irqchip, 0,
+ handle_simple_irq, IRQ_TYPE_NONE);
+ if (ret < 0) {
+ dev_err(dev, "failed to add irq chip: %d\n", ret);
+ goto out_gpiochip_remove;
+ }
+
+ ret = dln2_register_event_cb(pdev, DLN2_GPIO_CONDITION_MET_EV,
+ dln2_gpio_event);
+ if (ret) {
+ dev_err(dev, "failed to register event cb: %d\n", ret);
+ goto out_gpiochip_remove;
+ }
+
+ return 0;
+
+out_gpiochip_remove:
+ gpiochip_remove(&dln2->gpio);
+out:
+ return ret;
+}
+
+static int dln2_gpio_remove(struct platform_device *pdev)
+{
+ struct dln2_gpio *dln2 = platform_get_drvdata(pdev);
+ int i;
+
+ dln2_unregister_event_cb(pdev, DLN2_GPIO_CONDITION_MET_EV);
+ for (i = 0; i < dln2->gpio.ngpio; i++)
+ flush_work(&dln2->irq_work[i].work);
+ gpiochip_remove(&dln2->gpio);
+
+ return 0;
+}
+
+static struct platform_driver dln2_gpio_driver = {
+ .driver.name = "dln2-gpio",
+ .probe = dln2_gpio_probe,
+ .remove = dln2_gpio_remove,
+};
+
+module_platform_driver(dln2_gpio_driver);
+
+MODULE_AUTHOR("Daniel Baluta <***@intel.com");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 GPIO interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-gpio");
--
1.9.1
Octavian Purdila
2014-10-15 14:48:10 UTC
Permalink
Raw Message
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.

Signed-off-by: Octavian Purdila <***@intel.com>
---
drivers/gpio/gpiolib.c | 2 +-
include/linux/gpio/driver.h | 3 +++
2 files changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index 15cc0bb..3fa7e73 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -447,7 +447,7 @@ static int gpiochip_irq_map(struct irq_domain *d, unsigned int irq,
irq_set_lockdep_class(irq, &gpiochip_irq_lock_class);
irq_set_chip_and_handler(irq, chip->irqchip, chip->irq_handler);
/* Chips that can sleep need nested thread handlers */
- if (chip->can_sleep)
+ if (chip->can_sleep && !chip->irq_not_threaded)
irq_set_nested_thread(irq, 1);
#ifdef CONFIG_ARM
set_irq_flags(irq, IRQF_VALID);
diff --git a/include/linux/gpio/driver.h b/include/linux/gpio/driver.h
index e78a237..44161ac 100644
--- a/include/linux/gpio/driver.h
+++ b/include/linux/gpio/driver.h
@@ -56,6 +56,8 @@ struct seq_file;
* as the chip access may sleep when e.g. reading out the IRQ status
* registers.
* @exported: flags if the gpiochip is exported for use from sysfs. Private.
+ * @irq_not_threaded: flag must be set if @can_sleep is set but the
+ * IRQs don't need to be threaded
*
* A gpio_chip can help platforms abstract various sources of GPIOs so
* they can all be accessed through a common programing interface.
@@ -101,6 +103,7 @@ struct gpio_chip {
struct gpio_desc *desc;
const char *const *names;
bool can_sleep;
+ bool irq_not_threaded;
bool exported;

#ifdef CONFIG_GPIOLIB_IRQCHIP
--
1.9.1
Alexandre Courbot
2014-10-20 05:08:38 UTC
Permalink
Raw Message
On Wed, Oct 15, 2014 at 11:48 PM, Octavian Purdila
Post by Octavian Purdila
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Sorry if you already explained this (I have been a little bit late
with the GPIO reviews recently), but does this optimization bring a
significant benefit that justifies adding another field in struct
gpio_chip? If so it would be nice to have it in the commit message. If
not, do we need this at all?
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to ***@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Octavian Purdila
2014-10-20 10:19:12 UTC
Permalink
Raw Message
Post by Alexandre Courbot
On Wed, Oct 15, 2014 at 11:48 PM, Octavian Purdila
Post by Octavian Purdila
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Sorry if you already explained this (I have been a little bit late
with the GPIO reviews recently), but does this optimization bring a
significant benefit that justifies adding another field in struct
gpio_chip? If so it would be nice to have it in the commit message. If
not, do we need this at all?
Hi Alexandre,

In the case DLN2 USB GPIO adapter the GPIO interrupt is generated in
the completion routine of a receive URB, which means that we are in
interrupt context. If a threaded irq is used, we would have to
schedule work instead of running to interrupt handler directly which
is unnecessary and adds latency.

BTW, AFAIC Linus W already merged this patch in his next tree, I am
keeping it in this series because it was not pulled in the mfd-next
tree.

Thanks,
Tavi
Alexandre Courbot
2014-10-23 05:10:19 UTC
Permalink
Raw Message
On Mon, Oct 20, 2014 at 7:19 PM, Octavian Purdila
Post by Octavian Purdila
Post by Alexandre Courbot
On Wed, Oct 15, 2014 at 11:48 PM, Octavian Purdila
Post by Octavian Purdila
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Sorry if you already explained this (I have been a little bit late
with the GPIO reviews recently), but does this optimization bring a
significant benefit that justifies adding another field in struct
gpio_chip? If so it would be nice to have it in the commit message. If
not, do we need this at all?
Hi Alexandre,
In the case DLN2 USB GPIO adapter the GPIO interrupt is generated in
the completion routine of a receive URB, which means that we are in
interrupt context. If a threaded irq is used, we would have to
schedule work instead of running to interrupt handler directly which
is unnecessary and adds latency.
BTW, AFAIC Linus W already merged this patch in his next tree, I am
keeping it in this series because it was not pulled in the mfd-next
tree.
You're right, it's all good then. Thanks for the explanation.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-***@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Octavian Purdila
2014-10-15 14:48:09 UTC
Permalink
Raw Message
From: Laurentiu Palcu <***@intel.com>

This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.

Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.

[1] https://www.diolan.com/downloads/dln-api-manual.pdf

Signed-off-by: Laurentiu Palcu <***@intel.com>
Signed-off-by: Octavian Purdila <***@intel.com>
---
drivers/i2c/busses/Kconfig | 10 ++
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-dln2.c | 270 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 281 insertions(+)
create mode 100644 drivers/i2c/busses/i2c-dln2.c

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 2ac87fa..2f3f371 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -858,6 +858,16 @@ config I2C_DIOLAN_U2C
This driver can also be built as a module. If so, the module
will be called i2c-diolan-u2c.

+config I2C_DLN2
+ tristate "Diolan DLN-2 USB I2C adapter"
+ depends on MFD_DLN2
+ help
+ If you say yes to this option, support will be included for Diolan
+ DLN2, a USB to I2C interface.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-dln2.
+
config I2C_PARPORT
tristate "Parallel port adapter"
depends on PARPORT
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 49bf07e..4755f79 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -85,6 +85,7 @@ obj-$(CONFIG_I2C_RCAR) += i2c-rcar.o

# External I2C/SMBus adapter drivers
obj-$(CONFIG_I2C_DIOLAN_U2C) += i2c-diolan-u2c.o
+obj-$(CONFIG_I2C_DLN2) += i2c-dln2.o
obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o
obj-$(CONFIG_I2C_PARPORT_LIGHT) += i2c-parport-light.o
obj-$(CONFIG_I2C_ROBOTFUZZ_OSIF) += i2c-robotfuzz-osif.o
diff --git a/drivers/i2c/busses/i2c-dln2.c b/drivers/i2c/busses/i2c-dln2.c
new file mode 100644
index 0000000..62c38cd
--- /dev/null
+++ b/drivers/i2c/busses/i2c-dln2.c
@@ -0,0 +1,270 @@
+/*
+ * Driver for the Diolan DLN-2 USB-I2C adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ * i2c-diolan-u2c.c
+ * Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_I2C_MODULE_ID 0x03
+#define DLN2_I2C_CMD(cmd) DLN2_CMD(cmd, DLN2_I2C_MODULE_ID)
+
+/* I2C commands */
+#define DLN2_I2C_GET_PORT_COUNT DLN2_I2C_CMD(0x00)
+#define DLN2_I2C_ENABLE DLN2_I2C_CMD(0x01)
+#define DLN2_I2C_DISABLE DLN2_I2C_CMD(0x02)
+#define DLN2_I2C_IS_ENABLED DLN2_I2C_CMD(0x03)
+#define DLN2_I2C_WRITE DLN2_I2C_CMD(0x06)
+#define DLN2_I2C_READ DLN2_I2C_CMD(0x07)
+#define DLN2_I2C_SCAN_DEVICES DLN2_I2C_CMD(0x08)
+#define DLN2_I2C_PULLUP_ENABLE DLN2_I2C_CMD(0x09)
+#define DLN2_I2C_PULLUP_DISABLE DLN2_I2C_CMD(0x0A)
+#define DLN2_I2C_PULLUP_IS_ENABLED DLN2_I2C_CMD(0x0B)
+#define DLN2_I2C_TRANSFER DLN2_I2C_CMD(0x0C)
+#define DLN2_I2C_SET_MAX_REPLY_COUNT DLN2_I2C_CMD(0x0D)
+#define DLN2_I2C_GET_MAX_REPLY_COUNT DLN2_I2C_CMD(0x0E)
+
+#define DLN2_I2C_MAX_XFER_SIZE 256
+#define DLN2_I2C_BUF_SIZE (DLN2_I2C_MAX_XFER_SIZE + 16)
+
+struct dln2_i2c {
+ struct platform_device *pdev;
+ struct i2c_adapter adapter;
+ u8 port;
+ /*
+ * Buffer to hold the packet for read or write transfers. One
+ * is enough since we can't have multiple transfers in
+ * parallel on the i2c adapter.
+ */
+ void *buf;
+};
+
+static int dln2_i2c_enable(struct dln2_i2c *dln2, bool enable)
+{
+ int ret;
+ u16 cmd;
+ struct {
+ u8 port;
+ } tx;
+
+ tx.port = dln2->port;
+
+ if (enable)
+ cmd = DLN2_I2C_ENABLE;
+ else
+ cmd = DLN2_I2C_DISABLE;
+
+ ret = dln2_transfer(dln2->pdev, cmd, &tx, sizeof(tx),
+ NULL, NULL, NULL);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static int dln2_i2c_write(struct dln2_i2c *dln2, u8 addr,
+ u8 *data, u16 data_len)
+{
+ int ret;
+ struct {
+ u8 port;
+ u8 addr;
+ u8 mem_addr_len;
+ __le32 mem_addr;
+ __le16 buf_len;
+ u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+ } __packed *tx = dln2->buf;
+ unsigned len;
+
+ BUILD_BUG_ON(sizeof(*tx) > DLN2_I2C_BUF_SIZE);
+
+ tx->port = dln2->port;
+ tx->addr = addr;
+ tx->mem_addr_len = 0;
+ tx->mem_addr = 0;
+ tx->buf_len = cpu_to_le16(data_len);
+ memcpy(tx->buf, data, data_len);
+
+ len = sizeof(*tx) + data_len - DLN2_I2C_MAX_XFER_SIZE;
+ ret = dln2_transfer(dln2->pdev, DLN2_I2C_WRITE, tx, len,
+ NULL, NULL, NULL);
+ if (ret < 0)
+ return ret;
+
+ return data_len;
+}
+
+static int dln2_i2c_read(struct dln2_i2c *dln2, u16 addr, u8 *data,
+ u16 data_len)
+{
+ int ret;
+ struct {
+ u8 port;
+ u8 addr;
+ u8 mem_addr_len;
+ __le32 mem_addr;
+ __le16 buf_len;
+ } __packed tx;
+ struct {
+ __le16 buf_len;
+ u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+ } __packed *rx = dln2->buf;
+ unsigned rx_len = sizeof(*rx);
+
+ BUILD_BUG_ON(sizeof(*rx) > DLN2_I2C_BUF_SIZE);
+
+ tx.port = dln2->port;
+ tx.addr = addr;
+ tx.mem_addr_len = 0;
+ tx.mem_addr = 0;
+ tx.buf_len = cpu_to_le16(data_len);
+
+ ret = dln2_transfer(dln2->pdev, DLN2_I2C_READ, &tx, sizeof(tx),
+ rx, &rx_len, NULL);
+ if (ret < 0)
+ return ret;
+ if (rx_len < sizeof(rx->buf_len) + data_len)
+ return -EPROTO;
+ if (le16_to_cpu(rx->buf_len) != data_len)
+ return -EPROTO;
+
+ memcpy(data, rx->buf, data_len);
+
+ return data_len;
+}
+
+static int dln2_i2c_xfer(struct i2c_adapter *adapter,
+ struct i2c_msg *msgs, int num)
+{
+ struct dln2_i2c *dln2 = i2c_get_adapdata(adapter);
+ struct i2c_msg *pmsg;
+ struct device *dev = &dln2->pdev->dev;
+ int i;
+
+ for (i = 0; i < num; i++) {
+ int ret;
+
+ pmsg = &msgs[i];
+
+ if (pmsg->len > DLN2_I2C_MAX_XFER_SIZE) {
+ dev_warn(dev, "maximum transfer size exceeded\n");
+ return -EOPNOTSUPP;
+ }
+
+ if (pmsg->flags & I2C_M_RD) {
+ ret = dln2_i2c_read(dln2, pmsg->addr, pmsg->buf,
+ pmsg->len);
+ if (ret < 0)
+ return ret;
+
+ pmsg->len = ret;
+ } else {
+ ret = dln2_i2c_write(dln2, pmsg->addr, pmsg->buf,
+ pmsg->len);
+ if (ret != pmsg->len)
+ return -EPROTO;
+ }
+ }
+
+ return num;
+}
+
+static u32 dln2_i2c_func(struct i2c_adapter *a)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_BYTE | I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
+ I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static const struct i2c_algorithm dln2_i2c_usb_algorithm = {
+ .master_xfer = dln2_i2c_xfer,
+ .functionality = dln2_i2c_func,
+};
+
+static int dln2_i2c_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct dln2_i2c *dln2;
+ struct device *dev = &pdev->dev;
+ struct dln2_platform_data *pdata = dev_get_platdata(&pdev->dev);
+
+ dln2 = devm_kzalloc(dev, sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->buf = devm_kmalloc(dev, DLN2_I2C_BUF_SIZE, GFP_KERNEL);
+ if (!dln2->buf)
+ return -ENOMEM;
+
+ dln2->pdev = pdev;
+ dln2->port = pdata->port;
+
+ /* setup i2c adapter description */
+ dln2->adapter.owner = THIS_MODULE;
+ dln2->adapter.class = I2C_CLASS_HWMON;
+ dln2->adapter.algo = &dln2_i2c_usb_algorithm;
+ dln2->adapter.dev.parent = dev;
+ i2c_set_adapdata(&dln2->adapter, dln2);
+ snprintf(dln2->adapter.name, sizeof(dln2->adapter.name), "%s-%s-%d",
+ "dln2-i2c", dev_name(pdev->dev.parent), dln2->port);
+
+ platform_set_drvdata(pdev, dln2);
+
+ /* initialize the i2c interface */
+ ret = dln2_i2c_enable(dln2, true);
+ if (ret < 0) {
+ dev_err(dev, "failed to initialize adapter: %d\n", ret);
+ return ret;
+ }
+
+ /* and finally attach to i2c layer */
+ ret = i2c_add_adapter(&dln2->adapter);
+ if (ret < 0) {
+ dev_err(dev, "failed to add I2C adapter: %d\n", ret);
+ goto out_disable;
+ }
+
+ return 0;
+
+out_disable:
+ dln2_i2c_enable(dln2, false);
+
+ return ret;
+}
+
+static int dln2_i2c_remove(struct platform_device *pdev)
+{
+ struct dln2_i2c *dln2 = platform_get_drvdata(pdev);
+
+ i2c_del_adapter(&dln2->adapter);
+ dln2_i2c_enable(dln2, false);
+
+ return 0;
+}
+
+static struct platform_driver dln2_i2c_driver = {
+ .driver.name = "dln2-i2c",
+ .probe = dln2_i2c_probe,
+ .remove = dln2_i2c_remove,
+};
+
+module_platform_driver(dln2_i2c_driver);
+
+MODULE_AUTHOR("Laurentiu Palcu <***@intel.com>");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 I2C master interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-i2c");
--
1.9.1
Wolfram Sang
2014-10-16 06:58:52 UTC
Permalink
Raw Message
Post by Octavian Purdila
This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
For the I2C part:

Acked-by: Wolfram Sang <wsa-z923LK4zBo2bacvFa/***@public.gmane.org>

I assume this goes together with the other patches. If I should pick it,
let me know.
Loading...